Welcome to the TeslaFi support community.

Please enter your question, feature request, or issue below. Specific questions related to issues with your account can be sent privately by selecting "Or leave us a private message" below.

0

Sleep at specific locations

rocharms 7 years ago updated by BlueBella 6 years ago 1

I spend up to 12 hours at work during the day. Can there be two deep sleep time tables or maybe by location ie. when at work or home and idle for longer than 30 min enter deep sleep?

0

TAG a Charge (like TAG a drive)

BattMobile 7 years ago 0

I wanted to TAG all Charges Type-2 / CHAdeMo, etc. for some analysis, but I could see that I would want to TAG particular 3rd party Vendors, to check monthly-bill etc.

0
Not a bug

Added energy is missing from beginning of charging session

Veritas1980 7 years ago updated 7 years ago 2

I was wondering why my charging sessions at home showed very low efficiency in the beginning of a charge, and then evened more out over time.

It looks like it Teslafi does not count added energy in the first 5 minutes or so. The battery range and level is clearly going up, but the charge energy added is not counting.

Image 327


Answer
James 7 years ago

Hi.  Unfortunately this is not on TeslaFi's end.  The data comes directly from the API minute by minute and I'm not seeing this with my vehicle or a couple test vehicles I just checked.  When you start a charge you can view the raw API data by going to settings->account->advanced->view raw tesla api output and you'll see the same information that appears in the raw data page coming from the API.


It's possible that a reset of the vehicle could resolve it or it's a bug with 2018.6.1 641efac and your vehicle.  Or it's the battery management system adjusting the battery range at the beginning of the charge.  Unfortunately I don't have a definitive answer since there is no support from Tesla on the API.

0

Notification when Firmware Update overdue

BattMobile 7 years ago 0

My car stopped getting updates, it went in for service 2 months later and they pushed an update then which caused me not to have noticed the missing ones, and then a couple of months later I noticed that major update not received so sent a Support Request and got update the next day.


On Forums it seems that if update fails multiple times Tesla makes no follow up, and it is therefore up to the user to notify Tesla ...


... therefore it would be helpful to get Notice if my car (Model / Hardware) has not received a firmware update which has had widespread distribution.


Currently I get an Email "New firmware release detected for Model XXX with Hardware YYY" but this is increasingly less helpful as more models / hardware, and also I only want to chase Tesla if the update has had widespread release [i.e. for my Model / Hardware] (and its been, say, a week and I don't yet have it) and, ideally

0
Not a bug

Idle contains entry with "Shift State" set to "D"

StefanSarzio 7 years ago updated 7 years ago 2
0

Unlock Notification

Teddy 7 years ago updated by Silicon Desert 7 years ago 5

Would it be possible to add functionality to allow an email or push notification  to be sent when the car’s status changes from locked to unlocked when parked?

0

Logging events such as doors opening?

javhar 7 years ago 0

Is it possible to log events such as doors opening and closing (which the Tesla app does show), driver seat settings recall / save, etc?

0
Not a bug

Incorrect status of steering heater preconditioning

Sparks2067 7 years ago updated by James 7 years ago 1

Hi, it seems my car, the API or TeslaFi is confused about the status of the steering wheel

Image 300

heater. I went to the car and the wheel heater is not on but TeslaFi reports it as on. Climate is off and the car is locked and idling with charger connected.

0
Completed

Control button "Wake car" should be available when the car is offline

StefanSarzio 7 years ago updated 7 years ago 5

Right now my car is often listed as "offline". By opening the app I can "fix" this. I guess the app only sends a wake command. I would like to be able to do that from the web interface, like I can when the car's state is detected as "sleeping".