Selecting the hamburger and edit goes back to the charge search page.  This is when displaying a list of charges.

I tried to use a Tesla Supercharger but it errored out (red).  I then went to an adjacent stall and charged successfully.  TeslaFi is showing both the failed charge and the successful one with the same charge cost (matched to invoice).  So now the stats show double the cost for the day. 

I don't want to delete the charge attempt as want to keep it in my history.   How do I change the cost to zero?

On charges.php the column labels is inconsistent with how it uses the word average or its abbreviation.

In the AC Charging Totals section, two column headers are "Avg Efficiency" and "Avg. Time" (note the period in Avg. Time).

In the Supercharging Totals section one column header is "Average Time" with the word being written out in full.

It would be good to standardize the use of the word average.

I have a Tesla 3 Version 2022.44.25.3

Since couple of months I have bluetooth connectivity problems with my iphone 

While talking on the phone via bluetooth, phone connects and disconnects erratically

Have tried 3 different iphones, including a new one (iPhone 14 plus) but problem persists

Tesla Service is accessing/testing BT remotely and claims all is good

However it is not as until recently had no issues whatsoever

Have tried to disconnect/forget/reconnect phone and car but problem persists

On the other hand phone key works fine

Any suggestions will be greatly appreciated 

Thanks

There are only 3 cars similar to mine in terms of age and mileage. This makes the comparison somewhat meaningless. Would it be possible to add a parameter to select by  age OR by mileage? This would allow to have two different views with hopefully more cars to compare to, and determine whether mileage or age has the biggest impact on my car in terms of range.

Another feature that would be nice to have is to be able to select the bracket of mileage or age to include more cars in the comparison and compare to other "groups" of cars or to project my battery health into the future with my current usage profile.

Problem:
This morning I setup Schedule & Reminders for a Set Charge Limit at 8am.  TeslaFi did not log the new charging until 8:18am, because it was trying to sleep (Not polling). This is because I have the TeslaFi Sleep Mode Time To Try to Sleep and Nighttime, etc.  I would not like to change the TeslaFi Sleep Mode settings for when I have a Schedule & Reminder setup.
Suggestion:
If a Schedule & Reminders item will end up in the car not being able to sleep.  Then, TeslaFi should start polling for about 5 minutes. And, reset the TeslaFi sleep counter after 5 minutes.
This would only happen if the Schedule & Reminders item would end up in the car not being able to sleep, e.g. Set Charge Limit is higher then what the charge state is at now.

Hi,

We drive our ModelY to an off grid location and there is no cell coverage there. This leads to an interesting data artifact that I can be solved more correctly.

1) Internet on, car is sleeping

2) Interne is on, car wakes up

3) Internet is off, drive starts

4) Drive goes into cell coverage, first data report comes in

In the summary, this is reflected as

Sleep+Park -> High range loss

Drive -> Starting point on the map shown as our cabin, but distrance for drive is only the in range distance

The ODO reading shows me what happened. There is a jump from the last drive report finish ODO, to the start ODO of the drive when it enters cell coverage. The ODO gap is outside of cell coverage.

It would be nice to maybe reflect that part of the drive as a disconnected drive (data coverage 0%). So that the listing becomes

a) Sleep + Park

b) Disconnected drive (Start of next report ODO - Sleep ODO, Startr of next report battery level - Park bttery level)

c) Normal drive

Other small issue, if temperature increases during a Park event, the battery level often goes up (and is reported as such). However the range loss number is shown as a loss still, maybe it would be better to show a negative loss?

Thanks for all the work on the platform. It's super cool to have all this data. Love all the recent improvements.

Happy holidays!

Bas

I love the Fleet Software Tracker. I think all of the data after the "week" portion of the branch causes it to be a noisy when looking for what certain things like "what percentage of the fleet is on a version of the latest branch (currently 2022.44._). It would be cool if this data was either 1) shown separately, or 2) toggle that entire page to summarize the data by branch

Is it possible to display “New to FSD Beta” vehicles? Currently I don’t see any cars showing a “previous build” that’s NOT FSD Beta with a “current build” that IS FSD Beta. Would be nice to see how quickly Tesla is accepting vehicles in to the Beta Program.